US
ASTM B 150 C63020
European
EN 12163 CW307G
EN 12165 CW307G
EN 12167 CW307G
EN 12420 CW307G
EN 1653 CW307G
BS 2B 23
BS B 23
DTD 197A
BS 2874/2 CA104
DIN 17665 CuAl10Ni5Fe4
DIN 17672 CuAl10Ni5Fe4 WN 2.0966
NF L14-705 CuAl10Ni5Fe UA11N
NF A 51 -116 CuAl10Ni5Fe4
GAM MM 11 CuAl9Ni5Fe4
GAM MM 12
Typical applications for the BS 2B 23 nickel aluminium bronze material includes marine fasteners, hardware and fittings, thrust washers, gears, control bushes. Pump and valve components and forgings for marine assemblies
Aerospace
Landing gear components, wing actuators, and door hardware.
Mining, Offshore and General Engineering
Non-sparking safety tooling, valve stems and seats, wear plates, welding clamps, valve spindles and components, fasteners and bearing bushes for gas, oil, coal, mining, chemical and explosives industries.
Power Generation
Condenser end plates for steam generation equipment and desalination plants. Fire fighting equipment for off-shore platforms.
Tel +44 (0) 1782-816888
|
BS 2B 23
Nickel Aluminium Bronze
CuAl10Ni5Fe5
A British Nickel Aluminium Bronze where its unique combined properties of high strength, good fatigue, excellent corrosion resistance in sea water, non sparking and wear properties makes it a popular choice across the whole spectrum of industry.
BS 2B 23 (formerly BSB23) has very high anti galling properties when running against most grades of steels and is used around the world for aerospace landing gear bushes and bearings where its combination strength, fatigue, wear properties, shock resistance and corrosion resistance are well proven.
This is a wrought alloy that benefits from extreme consistency in properties, fine equiaxed grain structure and low cost volumetric inspection. Furthermore representative test pieces are taken giving accurate analysis of properties from material to component.
Element | Cu | Al | Ni+Co | Fe | Mn | Si | Sn | Zn | Pb | Imps |
---|---|---|---|---|---|---|---|---|---|---|
% | Bal | 8.5.0-11.0 | 4.0-5.5 | 4.0-5.5 | 0.5max | 0.2max | 0.1max | 0.4max | 0.05max | 0.5max |
Form | Size Range | Yield 0.5% | UTS | Elong | Hardness | |||
---|---|---|---|---|---|---|---|---|
Imperial | Metric | Ksi | MPa | Ksi | MPa | % | (HB) | |
Forged | 0.7-3.15" | >18-<=80mm | 55.1-65.2 | 380-450 | 101.5-120.4 | 700-830 | 16-24 | 180-230 |
Forged | >3.15" | >80mm | 47.8-54.8 | 330-378 | 101.5-107.3 | 700-740 | 20-25 | 180-193 |
With very little limitation on size, BS 2B 23 is available as standard in rod, bar, blocks, rings, tubes and discs up to a piece weight of 4,500kg/9,900lbs.
Copper Alloys is also regularly making customised shaped forgings and can increase piece weight up to 20,000kg/44,000lbs.
Copper Alloys Ltd also offers finished machined components in all alloys, complete project management and tailored mechanical properties beyond those of the specification to meet special requirements.
All information is supplied for guidance only and gives no guarantee for end applications
Metric | Metric | |
---|---|---|
Density | 0.275lb/in³ @ 68º F | 7612kg/m³ @ 20ºC |
Specific Gravity | 7.6 | 7.6 |
Specific Heat | 0.1 Btu/lb º F @68º F | 418.7 J/kg ºC @20 ºC |
Electrical Conductivity | 7-9 IACS @ 68º F | 4.1-5.2m/Ωmm²@20 ºC |
Thermal Conductivity | 22-27Btu.ft(hr.ft² º F) @68º F | 0.38-0.47 W/cm ºC @20 ºC |
Thermal Expansion | 9 x10ˉ 6 per º F (68-572 º F ) | 17 x10ˉ 6 perºC (20-300 ºC) |
Electrical Resistivity | 120-150Ω-cmil/ft @ 68º F | 19.1-24.6 µ Ω-cm@20 ºC |
Relative Magnetic Permeability | 1.5µ | |
Machining Index | 20 (Based on free machining brass 100%) | |
Modulus of Rigidity(heat treated) | 7.1-7.4 x10³ ksi | 48.9-51.0 GPa |
Modulus of Elasticity (heat treated) (In Tension) | 19-19.9 x10³ ksi | 131-137 GPa |
Fatigue Strength(rotating beam) | 50.5ksi @1x 106 | 348 Mpa@1x 106 |
Melting Range | 1940-1965 ºF | 1060-1075ºC |
Hot Working Range | 1560-1785 ºF | 850-975 ºC |
Cold Working | Limited | |
Cryogenic | Retains properties down to – 302 ºF | (-190 ºC) |
Elevated Temperatures | Retains properties to 662 ºF | (350 ºC) |
This Data is indicative only and must not be seen as a substitute for the full specification from which it is drawn. In particular, the mechanical property requirements vary widely with tempeter, product and product dimensions. The information is based on our present knowledge and is given in good faith. However, no liability will be acepted by the Company in respect of any action taken by any third party in reliance thereon.
As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose.
Any advice given by the Company to any third party is given for that party's assistance only and without liability on the part of the Company. Any contract between the Company and a customer will be subject to the Company's Conditions of Sale. The extent of the Company's liabilities to any customer is clearly set out in those Conditions, a copy of which is available on request.